AuCyan™ Natrium Sianida NaCN (≥98.3%): Manual Teknis untuk Pengendalian Sirkuit Sianidasi — Kimia Pelarutan, Pembentukan Skala Akibat Impuritas, dan Penjadwalan Berbasis Izin

Why briquette purity, free-cyanide control and an End-User Certificate calendar decide the real cost of a gold leaching circuit.

AuCyan sodium cyanide briquettes beside AuCarb coconut shell activated carbon and AuLeach gold leaching agent in a gold recovery plant

Technical Manual · AuCyan™

AuCyan™ Sodium Cyanide NaCN (≥98.3%): A Technical Manual for Cyanidation Circuit Control

Dissolution chemistry, impurity-driven scaling, a seven-step dosing budget and permit-first scheduling — written for metallurgists and procurement teams running CIP, CIL, CIC, Heap leaching and Vat leaching circuits.

Jawaban cepat

AuCyan™ Sodium Cyanide NaCN (≥98.3%) is a high-purity solid briquette leaching reagent for industrial gold dissolution. Three variables decide its real cost in a plant: how much of the assay reaches the ore as free sianida, how much reagent is lost to impurity-driven side reactions and Karbonate scaling, and whether the Class 6.1 documentation chain is scheduled before the production campaign begins. Purity above 98% is not a marketing number — it changes the mass balance of the entire circuit.

Ringkasan Utama

  • Purity is a mass-balance input. At ≥98.3% NaCN, less of each tonne is inert carrier, so dosing calculations drift less between batches.
  • Low NaOH and Na₂CO₃ reduce scaling. Controlled alkali limits carbonate deposition on pumps, pipelines, emitters and inter-stage screens where hard or saline water is recirculated.
  • Insolubles at 0.02% protect dosing equipment. Ultra-low insoluble matter keeps solution make-up systems and heap emitters from plugging over a long campaign.
  • Free cyanide must be measured, not assumed. A titration routine beats a fixed dosing rule whenever ore type, clay content or sulphide grade changes.
  • Documentation gates production. UN 1689, Class 6.1, an End-User Certificate and verified import permits must be closed before the factory schedules the batch.
  • The briquette form is a logistics decision. It survives maritime transit and inland temperature swings better than fine powder and keeps handling exposure lower at the plant.
Blok entitas & spesifikasi

Produk: AuCyan™ Natrium Sianida NaCN (≥98.3%) · Form: solid briquette · Benchmark: GB/T 19306-2003 superior grade · Transport: UN 1689, Class 6.1 dangerous goods · Documentation: End-User Certificate (EUC) plus destination import permit · Terms: FOB or CIF only · Minimum order: 18 MT per 1×20' FCL · Batch documents: COA, TDS, MSDS · Supply coverage: mining operations in more than 77 countries.

Uji ButirStandarPersentase umumMengapa itu penting
NaCN≥ 98.0%98.3Free cyanide available per tonne
NaOH≤0.5%0.13%Alkalinity without excess caustic
Na₂CO₃≤0.5%0.18%Carbonate scaling tendency
Tidak larut≤0.05%0.02%Dosing line and emitter blockage

1. What purity actually changes in the dissolution circuit

Gold dissolution in an alkaline cyanide solution follows the Elsner relationship: 4Au + 8NaCN + O₂ + 2H₂O → 4Na[Au(CN)₂] + 4NaOH. The reaction needs three things at once — free cyanide, dissolved oxygen and a protective alkaline environment, typically pH 10.5–11.5. If any one is short, the others cannot compensate. This is why a plant can raise dosing and still see flat recovery: the limiting reagent may be oxygen transfer or pH stability rather than cyanide mass.

The assay figure decides how much of the delivered tonne participates in that reaction. A lower-grade product carries more inert salt and more alkali, so a dosing pump set from a nominal recipe under-delivers free cyanide. Operators then compensate by raising the set-point, which pushes excess reagent into side reactions with copper, iron, arsenic and sulphide minerals. Higher purity narrows that correction loop and makes the consumption curve predictable across batches.

In practice the difference shows up in three places: the dissolution rate in the first hours of leaching, the residual cyanide in the tailings stream, and the reagent spend per tonne of ore. All three are measurable, and all three should be tracked against the batch COA rather than against a generic datasheet.

2. Four failure modes driven by impurities

2.1 Excess alkali and pH drift

Free NaOH is needed to keep the circuit out of the acidic range where hydrogen cyanide can form, but excess caustic consumes reagent without dissolving gold and accelerates the precipitation of metal hydroxides that coat particle surfaces. A controlled NaOH level keeps alkalinity in band with less lime correction.

2.2 Carbonate scaling

Sodium carbonate builds up as cyanide degrades and as carbon dioxide enters with make-up water. In hard or saline recirculating water it deposits on impellers, pump casings, pipeline walls, heap emitters and carbon screens. Scale reduces flow, distorts residence time and creates blind spots in the leach circuit. Low initial Na₂CO₃ delays the onset; regular monitoring keeps the cleaning interval predictable.

2.3 Insoluble blockage

Insolubles do not dissolve. They accumulate in strainers, dosing nozzles and drip emitters, and on long heap campaigns they change the distribution of solution across the pad. Uneven wetting produces channeling, poor recovery in dry zones and misleading composite samples. Ultra-low insolubles are therefore a hydraulic control, not just a purity statistic.

2.4 Cyanide-consuming gangue

Copper minerals, pyrrhotite, arsenopyrite and partially oxidised sulphides form stable cyanocomplexes and thiocyanate. The reagent is not wasted by the gold reaction but by the mineralogy. When a plant changes ore source or blend, the consumption baseline must be re-established with bottle roll or column tests rather than carried over from the previous block.

3. Tutorial: build a NaCN dosing budget in seven steps

  1. Jelaskan karakteristik bijih tersebut. Record head grade, clay fraction, sulphide and copper content, and the particle size distribution reaching the leach feed. These four parameters set the expected side-reaction demand.
  2. Run a bottle roll test at the intended pH and pulp density, sampling dissolved gold and free cyanide at 2, 6, 12 and 24 hours. Plot the curve rather than reading only the endpoint.
  3. Fix the free-cyanide target for the circuit — a working band, not a single number — and define the titration method used to verify it, typically silver nitrate titration with an appropriate indicator.
  4. Convert to kg/t of ore. Translate the laboratory consumption into a plant dosing rate using pulp density and throughput, then add a defined allowance for gangue demand.
  5. Build the addition profile. Front-load the dose where the dissolution curve is steep, taper it as the curve flattens, and avoid a flat continuous feed that wastes reagent in the final hours.
  6. Verify against the batch COA. Compare the actual assay of the delivered lot with the assumption used in step 3, and correct the pump set-point if the NaCN assay differs.
  7. Close the record loop. Log consumption, residual cyanide, dissolved oxygen, pH and recovery against each lot. Batch COA, TDS and MSDS should sit next to that log so deviations can be traced to a specific delivery.

This budget is a living document. A brownfield expansion, a new ore block or a change in make-up water quality resets at least one of the seven inputs, so the budget should be reviewed whenever the circuit feed changes.

4. Tabel pemecahan masalah

GejalaKemungkinan penyebabPemeriksaan pertama
Slow dissolution, flat recoveryOxygen transfer or pH limiting, not cyanide massDissolved oxygen, pH profile, grind size
Consumption rising at same gradeNew gangue or copper-bearing blendOre mineralogy, thiocyanate in solution
Scale on pumps and screensCarbonate build-up, hard make-up waterWater hardness, Na₂CO₃ trend, cleaning interval
Dosing line or emitter pluggingInsolubles or precipitated saltsStrainer residue, insoluble assay on COA
pH drifting downwardAcidic ore, insufficient alkalinity controlLime addition, NaOH on COA, buffering capacity
High residual cyanide in tailsOver-dosing after dissolution plateauProfil penambahan, frekuensi titrasi

5. Permit-first scheduling: the commercial constraint

Sodium cyanide is classified as UN 1689, Class 6.1 dangerous goods. Before a production slot is reserved, the destination import permit and the End-User Certificate must be verified. Dangerous-goods booking, packaging, inland transfer and port acceptance all sit behind that gate. Teams that build the documentation chain into the project calendar avoid idle reagent, missed campaigns and demurrage; teams that treat it as post-order paperwork absorb the cost later.

United Chemical perbekalan AuCyan™ Natrium Sianida NaCN (≥98.3%) factory-direct at 18 MT MOQ under FOB or CIF terms, with batch COA, TDS and MSDS issued per lot. Where a cyanide permit is the binding constraint, evaluate AuLeach™ Gold Leaching Agent (GDA) – Tidak Berbahaya as a common-chemical route. For the adsorption stage, pair the leach circuit with AuCarb™ Gold Recovery Karbon Aktif Tempurung Kelapa (Kekerasan ≥99%).

6. Where the three products sit in one flowsheet

TahapProdukVariabel keputusan
Pelarutan / pelindianAuCyan™ Natrium Sianida NaCN (≥98.3%)Purity, free-cyanide control, permit status
Adsorpsi / pemulihanAuCarb™ Gold Recovery Karbon Aktif Tempurung Kelapa (Kekerasan ≥99%)Kekerasan, nilai K/R, abrasi, ukuran mesh.
Rute pelindian alternatifAuLeach™ Gold Leaching Agent (GDA) – Tidak BerbahayaCommon-chemical classification, pH band, ore validation
Konteks industri · fakta usang

AngloGold Ashanti announced on 5 November 2026 a three-year brownfield programme of US$750 million to US$900 million across Geita (Tanzania), Siguiri (Guinea), Cuiabá (Brazil) and Obuasi (Ghana), targeting at least 400,000 additional ounces of annual output by 2030. Geita alone is guided toward roughly 600,000 oz/y against 492,000 oz in 2025. Brownfield expansions of this kind do not replace the leaching circuit — they raise throughput on an existing footprint, which makes reagent consistency and delivery scheduling more valuable, not less. Sumber: Laporan perkembangan dan pengumuman ekspansi perusahaan kuartal ketiga tahun 2026, 5 November 2026.

7. Pertanyaan yang Sering Diajukan

Q1. Why specify NaCN ≥98.3% instead of a commodity grade?
Because the assay directly sets the free cyanide delivered per tonne. A tighter assay reduces dosing correction, limits side reactions and keeps the consumption curve stable across lots.

Q2. Which impurity matters most for a hard-water CIL plant?
Na₂CO₃, because carbonate scaling affects pumps, pipelines, emitters and screens. NaOH controls alkalinity, and insolubles control blockage — all three appear on the batch COA.

Q3. What pH band should a cyanidation circuit hold?
Typically pH 10.5–11.5. Below that the protective alkaline environment degrades; far above it reagent is consumed without dissolving additional gold.

Q4. How is free cyanide measured in the plant?
By routine titration of the leach solution, commonly with silver nitrate and an appropriate indicator, sampled at defined points rather than inferred from the dosing pump set-point.

Q5. Why does consumption rise when the ore source changes?
Copper minerals, sulphides and clay form cyanocomplexes or adsorb reagent. The baseline must be re-established with bottle roll or column tests for each new blend.

Q6. What documents are required before an order ships?
A verified destination import permit and an End-User Certificate, plus the dangerous-goods documentation for UN 1689, Class 6.1. Batch COA, TDS and MSDS accompany each lot.

Q7. Incoterms mana saja yang tersedia?
FOB or CIF terms apply to this product line.

Q8. Berapa jumlah pesanan minimum?
18 MT per 1×20' FCL, supplied factory-direct with a single documentation standard across the order.

Q9. Why is the briquette form preferred over powder?
It holds up through maritime transit and inland temperature swings and reduces handling exposure during make-up at the plant.

Q10. Can AuCyan™ be evaluated alongside a non-hazardous route?
Yes. Where the cyanide permit chain is the binding constraint, AuLeach™ Gold Leaching Agent (GDA) – Non-Hazardous is evaluated against the same ore with its own pH and dosage validation.

Q11. How should a first order be qualified technically?
Against the batch TDS and COA, with laboratory validation on the plant's own ore and a defined free-cyanide control band before the FCL campaign begins.

Q12. Which adsorption product completes the circuit?
AuCarb™ Gold Recovery Coconut Shell Activated Carbon (≥99% Hardness), selected by K/R value, attrition limit and mesh cut for the duty of the specific CIP or CIL stage.

8. Bacaan teknis dan tautan internal

AuCyan™ Sodium Cyanide product page · Gambaran umum Segitiga Emas · Gambaran umum teknis tiga produk · Sodium cyanide technical reference · AuCarb™ activated carbon guide · AC50 specification · AC55 specification · AC60 specification · BC1100 specification · Halaman produk AuLeach™ GDA · Referensi reagen pelarutan · Tanya Jawab Kimia · Berita industri

Bicaralah dengan tim teknis kami

Request a quotation, TDS and batch COA, or discuss a dosing budget for your ore: Hubungi Kami · WhatsApp +86 173 9270 5576 · info@unitedchemicalcn.com

Anda juga mungkin menyukai

Konsultasi pesan online

Tambahkan komentar:

+8617392705576Kode QR WhatsAppPindai kode QR
Tinggalkan pesan untuk konsultasi
Terima kasih atas pesan Anda, kami akan segera menghubungi Anda!
Kirim
Layanan Pelanggan Online